DynaGlaze System

Tech Data Specific To DynaGlaze Top Coat Hardener

How to Use

SURFACE PREPARATION:

• Check moisture by ASTM D-4263. This method is done by taping (2 inch duct tape) a 4 mil clear plastic sheet to the surface. The sheet can remain on the surface for 16-24 hours. After this duration, the plastic sheet should be removed and the underside checked for moisture. If condensation appears on the under side of the film or the concrete becomes visibly damp, the concrete is not dry enough to place the wall system.
• All substrates must be sound, clean, dry and free from all contaminants and form release agents.
• Surface should be checked for soundness and any “hollow” areas should be removed. All depressions or spalled areas and cracks should be prefilled.
• Concrete should have laitance removed by sanding, wire brushing and/or grinding.
• Surfaces should be thoroughly vacuumed to remove surface dirt and dust.
• Surface and air temperature must be a minimum of 55°F during installation and cure.
• Provide sufficient air movement to prevent condensation on surface during installation.

APPLICATION INFORMATION:

Priming:

• After suitable preparation has been completed, mask all surfaces that require protection. If cove base is present, mask appropriately. Make certain all areas are covered that could be damaged by overspray.
• For concrete block, brick, etc.: apply a foundation coat of block filler per manufacturer’s recommendations and allow to dry.
• For drywall or gypsum sheetrock: apply commercial drywall sealer per manufacturer’s recommendations and allow sealer to dry.

Body Coats:

• Mix the DynaGlaze Top Coat Resin and DynaGlaze Top Coat Hardener independently using a variable speed drill and Jiffy mixer. Mix for two minutes or until uniform, exercising caution not to introduce air into the material.
• Blend together, equal parts of DynaGlaze Top Coat Resin and DynaGlaze Top Coat Hardener by volume and mix thoroughly.
• Pot life will be approximately four hours at 70°F.
• For spray application, run passes from floor to ceiling.
• For roller application, use 1/2”-3/4” nap roller.
• Apply one coat of DynaGlaze Top Coat at 266-400 sq.ft./gal.
• Allow to cure 2 hours at 70°F. Lower temperatures will require slightly longer cure time between coats.
• Apply second coat at 266-400 sq.ft./gal to obtain uniform hiding of substrate.

Cure Time:

At a cure temperature of 70°F, DynaGlaze Top Coat will cure to touch overnight. Full cure and specified chemical resistance require 14 days at 70°F.

LIMITATIONS:

• This product is not designed for exterior use or immersion.
• Proper material application is the sole responsibility of the user.
• Wood substrate not recommended due to dimensional instability.
• Concrete should not exceed 3% moisture content by mass (ASTM D-183-76).
• Previously painted surfaces are subject to inspection and approval.
• Store material in a cool, dry area (55-90°F) away from direct sunlight, flame or other hazards.
• Do not apply over honeycombed or structurally unsound surfaces.
• Before applying for protection against specific chemical environments, consult Chemical Resistance Guide.
• If the product is to be applied in or near areas containing foodstuffs, they should be removed before the application and until the coating has fully cured and all vapors have dissipated.
• Do not thin these products. Addition of thinners will slow the cure and reduce the ultimate properties of the products. Critical recoat times will also be affected.

CLEAN UP:

Tools should be cleaned right away with solvents such Xylene or UR-9 MCU THINNER. Any cured or hard material can be removed with the use of PC-46 DRY EZE. REFER TO MATERIAL SAFETY DATA SHEET FOR FURTHER SAFETY AND HANDLING INFORMATION. See individual labels for more caution statements. KEEP OUT OF THE REACH OF CHILDREN. DISPOSAL: Dispose in accordance with federal, state, and local regulations. Use licensed hazardous waste company. Empty containers may contain product residue, including flammable or explosive vapors. Do not cut, puncture or weld on or near container. All label warnings must be observed until the container has been commercially cleaned or reconditioned.

DynaGlaze RF

Tech Data

Tech Data Specific To DynaGlaze RF Hardener

How to Use

Surface Preparation

Check moisture by ASTM D-4263. This method is done by taping (2 inch duct tape) a 4 mil clear plastic sheet to the surface. The sheet can remain on the surface for 16-24 hours. After this duration, the plastic sheet should be removed and the underside checked for moisture. If condensation appears on the under side of the film or the concrete becomes visibly damp, the concrete is not dry enough to place the wall system. All substrates must be sound, clean, dry and free from all contaminants and form release agents. Surface should be checked for soundness and any “hollow” areas should be removed. All depressions or spalled areas and cracks should be properly repaired with the appropriate concrete repair & protection materials. Adhere to preparation and application instructions of the repair product used. Concrete should have laitance removed by sanding, or grinding. Surfaces should be thoroughly vacuumed to remove surface dirt and dust. Surface and air temperature must be a minimum of 55°F (12.7°C) during installation and cure. Provide sufficient air movement to prevent condensation on surface during installation. After suitable preparation has been completed, mask all surfaces that require protection. If cove base is present, mask appropriately. Make certain all areas are covered that could be damaged by overspray. DynaGlaze Top Coat can be spray-applied.) For new drywall, CMU or poured-in-place concrete walls, all DynaGlaze Systems can be pre-primed as outlined below.

* Ensure complete saturation of drywall substrate to minimize “soak in” of subsequent DynaGlaze System coats.

Mixing:

Mechanically premix the DynaGlaze RF Resin and DynaGlaze RF Hardener separately using a variable speed drill and Jiffy mixer (300-450 rpms). Mix for two minutes or until uniform, exercising caution not to introduce air into the material. Blend together 2.25 parts DynaGlaze RF Resin and 1 part DynaGlaze RF Hardener and mix thoroughly for 2 minutes.

Application:

Application of DynaGlaze RF Resin/DynaGlaze RF Hardener material use 3/8” nap roller, a 1/2’ nap roller may be required on certain substrates.

Cure Mechanism:

At a temperature of 70°F (21.1°C), allow the systems to cure a minimum of 3 days before use. DynaGlaze RF Resin 8-24 hours. Times based on 75°F(23.8°C), 50% relative humidity.

Critical Recoat Time:

DynaGlaze RF Resin/DynaGlaze RF Hardener is 8-24 hours based upon 75°F (23.8°C) and 50% relative humidity. Actual recoat time is to be determined by top coat.

Tooling and Finishing:

DynaGlaze RF Body Coat: Roller apply blended DynaGlaze RF Resin/DynaGlaze RF Hardener Finishing using a 3/8’’ nap roller cover.

Limitations:

• Minimum/Maximum substrate temperature: 60°F/85°F (15.5°C/30°C).
• Minimum/Maximum relative humidity: 10%/85%.
• Substrate temperature must be at least 5°F (3°C) above measured dew point.
• Determine the surface moisture content by using an impedance moisture meter designed for use on concrete as detailed in ASTM E-1907. Acceptable test results shall be 4% by mass or less.
• Do not use on exterior, on-grade substrates.
• Do not thin this product. Addition of thinners will slow the cure and reduce the ultimate properties of this product.
• Will discolor over time when exposed to sunlight (UV) and under certain artificial lighting conditions. UV resistant, light stable topcoats are available where ultimate color/clarity retention is required.
• Proper material application is the responsibility of the user.
• Do not apply if the wall, air, or material temperature is below 65°F(18.3°C) or over 90°F (32.2°C) or if the relative humidity is below 10% or above 80%. Do not apply over honeycombed or structurally unsound surfaces.
• If the product is to be applied in or near areas containing foodstuffs, they should be removed before the application and until the coating has fully cured and all vapors have dissipated.
• If there is any question as to whether or not the product will adhere to an existing coating, a test patch should be applied and evaluated for compatibility and adhesion.
• This product has a limited pot life.

Caution:

COMPONENT R: WARNING: IRRITANT, SENSITIZER Contains Modified Epoxy Resin (Mixture), Titanium Dioxide (CAS: 13463-67-7), Alkyl Glycidyl Ether (CAS: 68609-97-2) and Nonylphenol (CAS: 84852-15-3) May cause eye/skin/respiratory irritation. May cause skin and respiratory tract sensitization. May be harmful if swallowed.

COMPONENT H: DynaGlaze RF Hardener: WARNING: CORROSIVE, IRRITANT, SENSITIZER. Contains Amines (Mixture) and Benzyl Alcohol (CAS: 100-51-6). Harmful if swallowed. Corrosive to eyes. May cause eye/skin and respiratory tract burns. May cause respiratory tract / skin sensitization. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and central nervous system damage.

Deliberate concentration of vapors of ‘R’ &/or ‘H’ components for purposes of inhalation is harmful and can be fatal.

First Aid:

Eyes - Hold eyelids apart and flush thoroughly with water for 15 minutes. Skin - Remove contaminated clothing. Wash skin thoroughly for 15 minutes with soap and water. Inhalation - Remove to fresh air. Ingestion - Do not induce vomiting. Dilute with water. Contact physician. In all cases contact a physician immediately if symptoms persist.

Handling and Storage:

Avoid direct contact. Wear personal protective equipment (chemical resistant goggles/gloves/ clothing) to prevent direct contact with skin and eyes. Use only in well ventilated areas. Open doors and windows during use.

Clean Up:

Use a properly fitted NIOSH respirator if ventilation is poor. Wash thoroughly with soap and water after use. Remove contaminated clothing and launder before reuse. Use personal protective equipment (chemical resistant gloves/ goggles/clothing). Without direct contact, sweep up spilled or excess product and place in suitable sealed container. Dispose of excess product and container in accordance with applicable local, state, and federal regulations.

Additional Info:

Technical Data Sheets are updated periodically. Proper material application is the responsibility of the user. Before applying for protection against specific chemical environments, consult Chemical Resistance. Do not use over a putty coat. Do not apply over cementitious substrates containing more than 10% lime by volume. Concrete should not exceed 4% moisture content by mass (ASTM D-183-76). Previously applied finishes are subject to practical field evaluation to determine appropriate preparation, primers, etc. Masonry backings may require cement plaster finish if it is desirable to have the wall in perfect plane.

DynaGlaze RM

Tech Data

 Tech Data Specific To DynaGlaze RM Hardener

 How to Use

Surface Preparation

Check moisture by ASTM D-4263. This method is done by taping (2 inch duct tape) a 4 mil clear plastic sheet to the surface. The sheet can remain on the surface for 16-24 hours. After this duration, the plastic sheet should be removed and the underside checked for moisture. If condensation appears on the under side of the film or the concrete becomes visibly damp, the concrete is not dry enough to place the wall system. All substrates must be sound, clean, dry and free from all contaminants and form release agents. Surface should be checked for soundness and any “hollow” areas should be removed. All depressions or spalled areas and cracks should be properly repaired with the appropriate concrete repair & protection materials. Adhere to preparation and application instructions of the repair product used. Concrete should have laitance removed by sanding, or grinding. Surfaces should be thoroughly vacuumed to remove surface dirt and dust. Surface and air temperature must be a minimum of 55°F (12.7°C) during installation and cure. Provide sufficient air movement to prevent condensation on surface during installation. After suitable preparation has been completed, mask all surfaces that require protection. If cove base is present, mask appropriately. Make certain all areas are covered that could be damaged by overspray. DynaGlaze Top Coat can be spray-applied.) For new drywall, CMU or poured-in-place concrete walls, all DynaGlaze Systems can be pre-primed as outlined below.

* Ensure complete saturation of drywall substrate to minimize “soak in” of subsequent DynaGlaze System coats.

Mixing:

Mechanically premix the DynaGlaze RM Resin and DynaGlaze RM Hardener separately using a variable speed drill and Jiffy mixer (300-450 rpms). Mix for two minutes or until uniform, exercising caution not to introduce air into the material. Blend together 2.25 parts DynaGlaze RM Resin and 1 part DynaGlaze RM Hardener and mix thoroughly for 2 minutes.

Application:

Application of DynaGlaze RM Resin/DynaGlaze RM Hardener material use 3/8” nap roller, a 1/2’ nap roller may be required on certain substrates.

Cure Mechanism:

At a temperature of 70°F (21.1°C), allow the systems to cure a minimum of 3 days before use. DynaGlaze RM Resin 8-24 hours. Times based on 75°F(23.8°C), 50% relative humidity

Critical Recoat Time:

DynaGlaze RM Resin/DynaGlaze RM Hardener is 8-24 hours based upon 75°F (23.8°C) and 50% relative humidity. Actual recoat time is to be determined by top coat.

Tooling and Finishing:

DynaGlaze RM Body Coat: Fiberglass cloth is embedded into the freshly applied DynaGlaze RM Finishing Resin/DynaGlaze RM Hardener using a wallpaper hanging technique. Put cloth panels carefully or overlap panels and double cut, removing trimmed material. Use a broad knife, spring steel trowel or squeegee to remove air pockets and wrinkles after approximately 30 minutes to 2 hours, apply another full coat of blended DynaGlaze RM Resin/DynaGlaze RM Hardener at a rate of 240-260 sq.ft./gal(22.2 - 24.1m2/L) to embed fiberglass. Use a spring steel trowel or pliable plastic trowel to press the epoxy into the fiberglass; saturate and smooth. Allow to cure overnight or until surfaces can be sanded. Sand smooth. Imperfections should be filled with blended DynaGlaze RM epoxy and cabosil mixture. Repaired areas should be sanded smooth after cure. DynaGlaze RM System Grout Coat: If fiberglass has been properly embedded and smoothed, grouting will be minimal. Mechanically mix the DynaGlaze RM Resin and DynaGlaze RM Hardener separately using a variable speed drill and Jiffy mixer (300-450rpms). Mix for two minutes or until uniform, exercising caution not to introduce air into the material. Blend together 2.25 parts DynaGlaze RM Resin and 1 part DynaGlaze RM Hardener and mix thoroughly. Roller apply using a 3/8’’ nap roller cover. Tightly fill in all irregularities while grouting the entire surface. Option to use a broad knife, spring steel trowel or squeegee to smooth out the coating. Sand smooth after cured. Minor imperfections should be repaired using a gypsum-based grout (less than 5% gypsum).

Limitations

• Minimum/Maximum substrate temperature: 60°F/85°F (15.5°C/30°C).
• Minimum/Maximum relative humidity: 10%/85%.
• Substrate temperature must be at least 5°F (3°C) above measured dew point.
• Determine the surface moisture content by using an impedance moisture meter designed
for use on concrete as detailed in ASTM E-1907. Acceptable test results shall be 4% by
mass or less.
• Do not use on exterior, on-grade substrates.
• Do not thin this product. Addition of thinners will slow the cure and reduce the ultimate properties of this product.
• Will discolor over time when exposed to sunlight (UV) and under certain artificial lighting conditions. UV resistant, light stable topcoats are available where ultimate color/clarity retention is required.
• Proper material application is the responsibility of the user.
• Do not apply if the wall, air, or material temperature is below 65°F(18.3°C) or over 90°F (32.2°C) or if the relative humidity is below 10% or above 80%. Do not apply over
honeycombed or structurally unsound surfaces.
• If the product is to be applied in or near areas containing foodstuffs, they should be removed before the application and until the coating has fully cured and all vapors have dissipated.
• If there is any question as to whether or not the product will adhere to an existing coating, a test patch should be applied and evaluated for compatibility and adhesion.
• This product has a limited pot life.

Caution:

COMPONENT R: WARNING: IRRITANT, SENSITIZER Contains Modified Epoxy Resin (Mixture), Titanium Dioxide (CAS: 13463-67-7), Alkyl Glycidyl Ether (CAS: 68609-97-2) and Nonylphenol (CAS: 84852-15-3) May cause eye/skin/respiratory irritation. May cause skin and respiratory tract sensitization. May be harmful if swallowed. COMPONENT H: DynaGlaze RM Hardener: WARNING: CORROSIVE, IRRITANT, SENSITIZER. Contains Amines (Mixture) and Benzyl Alcohol (CAS: 100-51-6). Harmful if swallowed. Corrosive to eyes. May cause eye/skin and respiratory tract burns. May cause respiratory tract / skin sensitization. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and central nervous system damage.

Deliberate concentration of vapors of ‘R’ &/or ‘H’ components for purposes of inhalation is harmful and can be fatal.

First Aid:

Eyes - Hold eyelids apart and flush thoroughly with water for 15 minutes. Skin - Remove contaminated clothing. Wash skin thoroughly for 15 minutes with soap and water. Inhalation - Remove to fresh air. Ingestion - Do not induce vomiting. Dilute with water. Contact physician. In all cases contact a physician immediately if symptoms persist.

Handling and Storage:

Avoid direct contact. Wear personal protective equipment (chemical resistant goggles/gloves/ clothing) to prevent direct contact with skin and eyes. Use only in well ventilated areas. Open doors and windows during use.

Clean Up:

Use a properly fitted NIOSH respirator if ventilation is poor. Wash thoroughly with soap and water after use. Remove contaminated clothing and launder before reuse. Use personal protective equipment (chemical resistant gloves/ goggles/clothing). Without direct contact, sweep up spilled or excess product and place in suitable sealed container. Dispose of excess product and container in accordance with applicable local, state, and federal regulations.

Additional Info:

Technical Data Sheets are updated periodically. Proper material application is the responsibility of the user. Before applying for protection against specific chemical environments, consult Chemical Resistance. Do not use over a putty coat. Do not apply over cementitious substrates containing more than 10% lime by volume. Concrete should not exceed 4% moisture content by mass (ASTM D-183-76). Previously applied finishes are subject to practical field evaluation to determine appropriate preparation, primers, etc. Masonry backings may require cement plaster finish if it is desirable to have the wall in perfect plane.