Premier Patch 1000
Tech Data
| Packaging | Available in 3 different kit sizes, all of which include: urethane, polyurea, and aggregate. The only difference between the kits is their size. 2 Gallon, 4 Gallon & 8 Gallon Kits. |
|---|---|
| Color | Natural Color |
| Appearance & Odor | Thin liquid; mild aromatic odor |
| Flammable Limits (In Air By Volume) | Lower: N/A, Upper: N/A |
| Toxicity | Low |
| Flash Point | 245°F (118.3°C) |
| Boiling Point | >300°F (>148.9°C) |
| Application Temperature Range | 0°F (-17.8°C) – 90°F (32.2°C) |
| Volume Mix Ratio | 1:1 |
| Viscosity (Mixed) | 20 CPS Typical |
| Solids Content (%) | 60% (ASTM D-1464) |
| Hardness (Shore D) | 70 (ASTM D-2240) |
| VOC | 416 g/l (EPA method 24) |
| UV Resistance | Poor (QUV) |
| Working Time | 2-3 minutes (at 75°F, 24°C) |
| Recoat Time | 10-15 minutes (at 75°F, 24°C) |
| ‘Open’ To Foot Traffic | 5 minutes (at 75°F, 24°C) |
| ‘Open’ To Vehicle Traffic | 10 minutes (at 75°F, 24°C) |
| Specific Gravity (H2O=1) | 1.0 |
| Material Stability | Stable |
| Conditions To Avoid | Heat, open flame, sparks |
| Extinguishing Media | Foam, CO2, Dry Chemical |
| Hazardous Decomposition / By Products | Carbon Dioxide, Carbon Monoxide, Nitrogen Oxide trace amounts of Hydrogen Cyanide |
| Shelf Life | 1 Year In Unopened Container |
Tech Data Specific To Part “A” or Part “B”
Part "A"
| Vapor Density | N/A |
|---|---|
| Solubility In Water | Reacts with water |
| Evaporation | N/A |
| Incompatibility (Materials To Avoid) | Strong Oxidizing Agent, Water, Alcohol |
Part "B"
| Vapor Density | Heavier than air |
|---|---|
| Solubility In Water | N/A |
| Evaporation | Slower than ether |
| Incompatibility (Materials To Avoid) | Isocyanates & Strong Oxidizing Agent |
LIMITATIONS & FOR BEST RESULTS:
- Do not thin this product.
- Deeper holes may require primer the surface with ‘neat’ liquid.
- Mix only enough product that can be used within 5 minutes.
- When re-coating, always apply the next coat within 24 hours of completing the previous coat.
- Do not apply this product heavier / thicker than the recommended spread rate / mil thickness.
PRODUCT APPLICATION:
Apply using steel trowel or patching blade. Superior Industries product test data is based on environmental temperatures of 750 F (240 C). Viscosity and working time are always affected by temperatures above or below that mark. When applying product – always consider the ambient, surface, and product temperature at the time and place of installation.
COLOR AND TEXTURES:
Premier Patch 1000 is available in natural only.
CHEMICAL RESISTANCE:
Always refer to Superior Industries’ chemical resistant chart for specific information or contact Superior Industries directly.
PRODUCT STORAGE:
DO NOT allow Superior Industries products to freeze. All Superior Industries products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 500 F (100 C).
SURFACE PREPARTION:
Always apply Superior Industries products to a ‘clean / sound’ substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is unavoidable always perform tests to determine adhesion and compatibility to the existing substrate.
Surface preparation by means of a shot-blasting machine is the best and recommended method for attaining the desired profile. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
CLEAN UP:
Application tools and equipment can be cleaned with Dynasolve or Toluene.
DISPOSAL:
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
IMPORTANT NOTICE:
Always read and acquaint yourself with Superior Industries’ Product Data Sheet, MSDS [material safety data sheet], and product labels for each individual product prior to mixing and prior to use.
For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact Superior Industries directly for recommendations.
Recommended Application / Mixing Instructions
NOTE : Premier Patch 1000 is an ultra-rapid curing product, DO NOT mix more product than can be USED / placed in 5 minutes.
METHOD A – 'Blended' Method
- Combine equal parts of component A and component B, mix thoroughly with a paint mixing stick (or a small 3/8” or 1/2” drill equipped with a small spiral mixing blade) – for approx. 30 to 60 seconds.
- Prior to adding sand, use a disposable brush to prime the area to be patched with the blended / ‘neat’ product.
- Once primed, immediately blend the appropriate sand with the remaining mixed liquid, and pour the contents into the area to be filled / patched.
- Smooth and level off the material with a trowel or drywall type knife.
- Allow the patch to cure [approx. 15 minutes depending on temperatures] and grind the surface as needed to match the adjacent surface.
METHOD B – 'Layered' Method
- Combine equal parts of component A and component B, mix thoroughly with a paint mixing stick (or a small 3/8” or 1/2” drill equipped with a small spiral mixing blade) – for approx. 30 to 60 seconds.
- Pour the mixed contents into the area to be filled / patched, and immediately broadcast sand over ‘wet’ liquid until it appears dry.
- Repeat steps 1 & 2, as needed, until area if filled to the level of the surrounding surface.
- Smooth and level off the material with a trowel or drywall type knife.
- Allow the patch to cure [approx. 15 minutes depending on temperatures] and grind the surface as needed to match the adjacent surface.