Chlorinated Rubber Pool Paint
5-7 Year Protection | Fortified With Silicone
Dries Quickly | Use On Concrete & Plaster
The Ultimate in Swimming Pool Coatings
DynaKote 1000 is fast-curing, long-lasting, and the only chlorinated rubber pool paint fortified with UV additives and silicone, providing an extended life of 5 to 7 years. DynaKote 1000 cures quickly and resists fading, offering excellent color retention and strong protection against to UV rays and chlorine. This longer lasting, silicone fortified pool coating can be applied to bare concrete or plaster – even over most other chlorinated rubber pool paints – and is the paint of choice for finishing new pools and refinishing old ones. DynaKote 1000 is available in 6 colors: white, aqua, sky blue, medium blue, royal blue, & black.
White, Aqua, Sky Blue, Medium Blue, Royal Blue, & Black
This durable, fast drying rubber coating utilizes silicone and UV stabilizers to block out those harmful rays of sunlight. It provides long term waterproof protection and is resistant to chemicals and abrasion. DynaKote 1000 was formulated to be the best protectant against UV rays, fading, chlorine, chemicals, abrasion from automatic pool cleaning machines, algae, alkali, mineral oils, and both fresh and salt water. DynaKote 1000 is easy to apply and easy to recoat.
UV Rays • Fading • Chlorine • Chemicals • Abrasion • Algae • Alkali • Mineral Oils • Fresh & Salt Water
Get that fresh pool look today by applying one of the many colors of DynaKote 1000. Each color naturally dries with a gloss finish, but if you would prefer a non-slip finish you can add sand, marble dust, or pumice stone to the paint as desired. This extended life pool paint can be applied over other good condition chlorinated rubber pool paints. No primer is needed – DynaKote 1000 is a self priming paint. DynaKote 1000 can be expected to cover 300-400 square feet per gallon, and two coats will be needed for proper application.
Self Priming | Will Not Fade
DynaKote 1000 is available in both 1 gallon cans and 5 gallon pails.
This high solids chlorinated rubber pool coating is dry to the touch in about 1 hour (at 75°F, 24°C) and can be re-coated after 24 hours if desired. The pool can be filled again with water after DynaKote 1000 has had 5 days to completely cure.
It offers a coverage range of 300-400 sq ft per gallon (at 2 mils dry) and its recommended thickness is 4 mils dry, so 2 full coats are required. Note that 50% less coverage results from use on rough, bare, or sandblasted surfaces. If you’re trying to figure out how much paint your pool job will require, here’s a helpful equation: Length x Width x 1.7 = square footage x 2 (2 coats) / 300 square feet = gallons of paint needed.
Instructions: Proper surface preparation is very important to the successful application of DynaKote 1000. We recommend that you read the product label carefully before you begin the application process. Before applying this paint, mix it mechanically for 10 minutes and apply straight from container, thinning with solvent reducer or high flash naphtha as needed for optimal performance. To apply, simply spray, brush, or roll DynaKote 1000 on with a 3/8” nap roller. When rolling (which is the preferred application form), keep the roller wet and roll in one direction, rewet it, then cross roll. When spraying, use a conventional air sprayer (50-70 psi, tip size .055-.070) or an airless sprayer (2200-2500 psi, tip size .019-.023). Do not apply DynaKote 1000 if substrate, material, or ambient temperature is not between 50°F (10°C) and 95°F (35°C). Note that DynaKote 1000 is not intended for use on vinyl lined pools, metal pools, fiberglass, spas, or whirlpools.
We at Superior welcome your questions and inquiries. Call us anytime toll free at 800-476-2072