Epoxy Swimming Pool Paint
Pro Master Pool Coating
7-10 Year Protection | Pools & Spas
Concrete, Plaster, Fiberglass, & Gunite
Alternative To Plaster
A two-part epoxy high build pool paint, Pro Master Pool Coating is 80% solids and is the finest pool paint on the market today. Pro Master Pool Coating offers an extended life of 7 to 10 years, and it can be used in pools or spas – even on imperfect surfaces. This epoxy swimming pool paint can be applied to bare concrete, plaster, fiberglass, and gunite, and can also be applied over most other types of epoxy pool coatings.
Pro Master Pool Coating is fast-drying, long-lasting, and can be used as instead of plaster, offering an economical alternative to replastering your pool. It is formulated with a specially compounded chemical which is able to keep it from fading and protect it from the harmful effects of UV rays. It offers excellent color retention, as well as strong protection against chlorine and other harmful substances. Compounded using a special silicone additive, this premium pool coating is the paint of choice for finishing new pools and spas and refinishing old ones. Pro Master Pool Coating dries in a ceramic-like tile finish and is available in 6 colors: white, aqua, sky blue, medium blue, royal blue, and black.
Available In: White, Aqua, Sky Blue, Medium Blue, Royal Blue, & Black
Provides For A Tile-Like Finish
This 80% solids epoxy pool paint has excellent fill qualities that allow it to perfect imperfect pool surfaces and seal hairline cracks. This durable coating utilizes silicone and UV stabilizers to block out harmful rays of sunlight, inhibiting algae growth and protecting against fading and chalking. It provides long term resistance against chemicals, abrasion, and stains. Pro Master Pool Coating was formulated to offer the best possible protection against UV rays, fading, chlorine, chemicals, stains, abrasion from automatic pool cleaning machines, shock, algae, alkali, mineral oils, and both fresh and salt water. No other swimming pool paint is able to withstand these harsh substances and offer such long term protection against fading.
• UV Rays • Fading • Chlorine • Chemicals • Stains • Abrasion • Shock • Algae • Alkali • Mineral Oils • Fresh & Salt Water
Get that fresh, clean pool look today by applying one of the many colors of Pro Master Pool Coating. Each color naturally dries with a gloss finish, but if you would prefer a non-slip finish you can add sand, marble dust, or pumice stone to the paint as desired. This extended life epoxy swimming pool paint can be applied over most other good condition epoxy pool coatings. No primer is needed – Pro Master Pool Coating is a self priming paint. Pro Master Pool Coating can be expected to cover 250 square feet per gallon, and two coats will be needed for proper application. This solvent based high build coating has a heavy duty 1:1 mix ratio.
Self Priming | Dries Quickly | Will Not Fade | 1:1 Mix Ratio
Pro Master Pool Coating is available in both 2 gallon kits and 10 gallon kits. This 80% solids pool coating is dry to the touch in about 6-8 hours (at 75°F, 24°C) and can be re-coated with no sanding required between 16 and 72 hours if desired. The pool can be filled again with water after Pro Master Pool Coating has had 5 days to completely cure. Use Xylene to thin and clean up. This premium epoxy swimming pool paint offers a coverage range of approximately 500 square feet per 2 gallon kit, and two full coats are required. Note that 50% less coverage results from use on rough, bare, or sandblasted surfaces. If you’re trying to figure out how much paint your pool job will require, here’s a helpful equation: Length x Width x 1.7 = square footage x 2 (2 coats) / 500 (coverage per 2 gallon kit) = kits needed. (Note that this equation assumes a purchase of a 2 gallon kit; make the necessary adjustments for a 10 gallon kit order.)
Instructions: Proper surface preparation is very important to the successful application of Pro Master Pool Coating. We recommend that you read the product label carefully before you begin the application process. Before applying this paint, mechanically mix Part A and Part B separately for 10 minutes, then combine them (1:1 mix ratio) and mix together mechanically for 10 more minutes. Only mix what you can apply within 4 hours. Allow 30 minutes to induct before applying. Thin with an epoxy reducer or high flash naphtha as needed for optimal performance. To apply, simply spray, brush, or roll on. When rolling (which is the preferred application form), use a 3/8” or ½” nap mohair, metal, lambskin, or phenolic core roller and keep it wet, rolling in one direction, rewetting, and then cross rolling. When spraying, use a conventional air sprayer (50-70 psi, tip size .055-.070) or an airless sprayer (2200-2500 psi, tip size .019-.023). Do not apply Pro Master Pool Coating if substrate, material, or ambient temperature is not between 50°F (10°C) and 95°F (35°C). Note that Pro Master Pool Coating is not intended for use on vinyl lined pools or metal pools.